Stringing or Oozing
Stringing or Oozing
Stringing (otherwise known as oozing, whiskers, or “hairy” prints) occurs when small strings of plastic are left behind on a 3D printed model. This is typically due to plastic oozing out of the nozzle while the extruder is moving to a new location. Thankfully, there are several settings within Simplify3D that can help with this issue. The most common setting that is used to combat excessive stringing is something that is known as retraction. If retraction is enabled, when the extruder is done printing one section of your model, the filament will be pulled backwards into the nozzle to act as a countermeasure against oozing. When it is time to begin printing again, the filament will be pushed back into the nozzle so that plastic once again begins extruding from the tip. To ensure retraction is enabled, click “Edit Process Settings” and click on the Extruder tab. Ensure that the retraction option is enabled for each of your extruders. In the sections below, we will discuss the important retraction settings as well as several other settings that can be used to combat stringing, such as the extruder temperature settings.
Retraction distance
The most important retraction setting is the retraction distance. This determines how much plastic is pulled out of the nozzle. In general, the more plastic that is retracted from the nozzle, the less likely the nozzle is to ooze while moving. Most direct-drive extruders only require a retraction distance of 0.5-2.0mm, If you encounter stringing with your prints, try increasing the retraction distance by 1mm and test again to see if the performance improves.
Retraction speed
The next retraction setting that you should check is the retraction speed. This determines how fast the filament is retracted from the nozzle. If you retract too slowly, the plastic will slowly ooze down through the nozzle and may start leaking before the extruder is done moving to its new destination. If you retract too quickly, the filament may separate from the hot plastic inside the nozzle, or the quick movement of the drive gear may even grind away pieces of your filament. There is usually a sweet spot somewhere between 1200-6000 mm/min (20-100 mm/s) where retraction performs best. But the ideal value can vary depending on the material that you are using, so you may want to experiment to see if different speeds decrease the amount of stringing that you see.
Temperature is too high
Once you have checked your retraction settings, the next most common cause for excessive stringing is the extruder temperature. If the temperature is too high, the plastic inside the nozzle will become less viscous and will leak out of the nozzle much more easily. However, if the temperature is too low, the plastic will still be somewhat solid and will have difficulty extruding from the nozzle. If you feel you have the correct retraction settings, but you are still encountering these issues, try decreasing your extruder temperature by 5-10 degrees. This can have a significant impact on the final print quality.
Long movements over open spaces
As we discussed above, stringing occurs when the extruder is moving between two different locations, and during that move, plastic starts to ooze out of the nozzle. The length of this movement can have a large impact on how much oozing takes place. Short moves may be quick enough that the plastic does not have time to ooze out of the nozzle. However, long movements are much more likely to create strings. Thankfully, Simplify3D includes an extremely useful feature that can help minimize the length of these movements. The software is smart enough that it can automatically adjust the travel path to make sure that nozzle has a very short distance to travel over an open space. In fact, in many cases, the software may be able to find a travel path that avoids crossing an open space all together! This means that there is no possibility to create a string, because the nozzle will always be on top of the solid plastic and will never travel outside the part. To use this feature, click on the Advanced tab and enable the “Avoid crossing outline for travel movement” option.
Movement Speed
Finally, you may also find that increasing the movement speed of your machine can also reduce the amount of time that the extruder can ooze when moving between parts. You can verify what movement speeds your machine is using by clicking on the Speeds tab of your process settings. The X/Y Axis Movement Speed represents the side-to-side travel speed, and is frequently directly related to the amount of time your extruder spends moving over open air. If your machine can handle moving at higher speeds, you may find that increasing this settings can also reduce stringing between parts
Popular Articles
SMPS not turning ON
SMPS may not turn because of these reasons. 1. SMPS is not getting power supply. 2. SMPS is spoilt 3. SMPS is detecting a short in machine circuit and is auto Shutting. Troubleshooting: Note: Checking SMPS input when machine is on is risky task. You ...Layer Shifting caused by pulley slipping down
Motor Pulley is mounted on Motor shaft with the help of a grub screw. The pulley acts as a bridge for transferring the motors rotary motion to the belts. The motor pulley comes under high stresses and sometimes may get displaced. The displacement of ...Troubleshooting Limit switch issues.
Fracktal 3d Printers come with 3 Limit switches. X axis Y axis Z axis Whenever these switches fail the printer faces certain issues like not being able to move in certain direction or going and crashing at the edges. Below we have listed out the ...Pro Maintainance
MaintainanceBuying a 3D printer.
3D printing technology is broadly classified into FDM, SLA and SLS printing. We at Fracktal works Manufacture and sell machines related to FDM and SLA. If you need parts printed using SLS you can use our Fractory service. We have mentioned few of the ...
Recent Articles
Removing carriage board - Julia Extended.
Carriage board is a small board mounted on the carriage. To remove the carriage board follow the steps below. Note: Remove filament before removing carriage cover. 1. Remove carriage cover. The carriage cover is fastened by 2 screws. Please be ...Sending Gcode to Fracktal care for troubleshooting.
Analysing the Gcode is one among the primary steps done while troubleshooting issues. The gcode which may be fine in your system may get corrupted while uploading to your printer. To make sure this corruption has not happened we recommend analysing ...Material (filament) storage SOP
3D printing filaments are hygroscopic in nature. PLA Nylon and PVA are extremly hygroscopic and storing them in air tight containers with dessicants is a must. Other filaments also need to be stored in air tight container but can be exposed to ...SMPS not turning ON
SMPS may not turn because of these reasons. 1. SMPS is not getting power supply. 2. SMPS is spoilt 3. SMPS is detecting a short in machine circuit and is auto Shutting. Troubleshooting: Note: Checking SMPS input when machine is on is risky task. You ...Changing SMPS- Extended.
Fractal Printers are designed with serviceability in mind. Changing SMPS in Julia Extended can be done with the help of a + Screw driver and 2.5mm Allen key (Allen Key is provided with the Accessory box). Steps to replace SMPS: 1. Switch off the ...