SOP of the printer
Related Articles
The printer does not turn on
If your printer doesn't turn on, or it keeps turning off during preheating, the most common causes are either a wrong voltage on the PSU or a blown fuse. The printer does not turn on If your printer does not turn on at all, then there might be a more ...How to make complete use of your accessories box.
The accessories box contains these Accessories. Power cable: Please connect the power cable to the power socket in your printer and connect it to 3pin power socket. PTFE Tube: PTFE tube is used to avoid tangling of filament and rubbing of filament ...Thermal Runway, System Stopped Error
Fracktal printers come with inbuilt feature to avoid accidents by over heating of the nozzle or heater cartridge. Due to some issue with printer if the heater cartridge heats beyond certain temperature it can lead to melting of hot end and also fire ...Error: Heating failed, system stopped! Heater_ID: Bed
This error is show when the Bed does not reaches the required temperature as set by the machine. To confirm that the error is related to bed you can check the last word of the error which says "Bed". Schematics of Heater wiring. This error comes ...Small size print failure
Top of pawn is melted due to improper cooling. Overheating The plastic that exits your extruder may be anywhere from 190 to 310 degrees Celsius. While the plastic is still hot, it is pliable and can easily be formed into different shapes. However, as ...
Popular Articles
SMPS not turning ON
SMPS may not turn because of these reasons. 1. SMPS is not getting power supply. 2. SMPS is spoilt 3. SMPS is detecting a short in machine circuit and is auto Shutting. Troubleshooting: Note: Checking SMPS input when machine is on is risky task. You ...Layer Shifting caused by pulley slipping down
Motor Pulley is mounted on Motor shaft with the help of a grub screw. The pulley acts as a bridge for transferring the motors rotary motion to the belts. The motor pulley comes under high stresses and sometimes may get displaced. The displacement of ...Troubleshooting Limit switch issues.
Fracktal 3d Printers come with 3 Limit switches. X axis Y axis Z axis Whenever these switches fail the printer faces certain issues like not being able to move in certain direction or going and crashing at the edges. Below we have listed out the ...Pro Maintainance
MaintainanceBuying a 3D printer.
3D printing technology is broadly classified into FDM, SLA and SLS printing. We at Fracktal works Manufacture and sell machines related to FDM and SLA. If you need parts printed using SLS you can use our Fractory service. We have mentioned few of the ...
Recent Articles
Removing carriage board - Julia Extended.
Carriage board is a small board mounted on the carriage. To remove the carriage board follow the steps below. Note: Remove filament before removing carriage cover. 1. Remove carriage cover. The carriage cover is fastened by 2 screws. Please be ...Sending Gcode to Fracktal care for troubleshooting.
Analysing the Gcode is one among the primary steps done while troubleshooting issues. The gcode which may be fine in your system may get corrupted while uploading to your printer. To make sure this corruption has not happened we recommend analysing ...Material (filament) storage SOP
3D printing filaments are hygroscopic in nature. PLA Nylon and PVA are extremly hygroscopic and storing them in air tight containers with dessicants is a must. Other filaments also need to be stored in air tight container but can be exposed to ...SMPS not turning ON
SMPS may not turn because of these reasons. 1. SMPS is not getting power supply. 2. SMPS is spoilt 3. SMPS is detecting a short in machine circuit and is auto Shutting. Troubleshooting: Note: Checking SMPS input when machine is on is risky task. You ...Changing SMPS- Extended.
Fractal Printers are designed with serviceability in mind. Changing SMPS in Julia Extended can be done with the help of a + Screw driver and 2.5mm Allen key (Allen Key is provided with the Accessory box). Steps to replace SMPS: 1. Switch off the ...