Service Report

Service Report

Service report 2018:

1. Issue Identified: Limit switch replaced.

2. Resolution provided:

3. Customer comments/requests:

4. Additional tasks created:

5. Service fee if any:

6. Spares provided:

7. Invoice number for additional spares provided:

8. Customer acceptance signature:

9. Feedback:




Emergency contact: 
Fracktal Works Pvt. Ltd.
C272, 7th Cross,
Peenya Stage I,
Bangalore
560058

    • Related Articles

    • Hotend Assembly

      The hotend assembly * Nozzle (0.4mm) * Heater block (Steel block) * Heating cartridge * Thermistor  Nozzle swap procedure: * To replace the nozzle, first wait for the nozzle to cool down. Then gently pull down the (green) connector. * Use an M3 allen ...

    • Fracktory software, User manual and Quick start Video

      Here is the download link for the latest Fracktory: http://printers.fracktory.in/download Kindly register with us via the software to avail special offers and updates from Fracktal. The user manual also describes the best practices to use the ...

    • Popular Articles

    • SMPS not turning ON

      SMPS may not turn because of these reasons. 1. SMPS is not getting power supply. 2. SMPS is spoilt 3. SMPS is detecting a short in machine circuit and is auto Shutting. Troubleshooting: Note: Checking SMPS input when machine is on is risky task. You ...

    • Layer Shifting caused by pulley slipping down

      Motor Pulley is mounted on Motor shaft with the help of a grub screw. The pulley acts as a bridge for transferring the motors rotary motion to the belts. The motor pulley comes under high stresses and sometimes may get displaced. The displacement of ...

    • Troubleshooting Limit switch issues.

      Fracktal 3d Printers come with 3 Limit switches. X axis  Y axis Z axis Whenever these switches fail the printer faces certain issues like not being able to move in certain direction or going and crashing at the edges. Below we have listed out the ...

    • Pro Maintainance

      Maintainance

    • Buying a 3D printer.

      3D printing technology is broadly classified into FDM, SLA and SLS printing. We at Fracktal works Manufacture and sell machines related to FDM and SLA. If you need parts printed using SLS you can use our Fractory service. We have mentioned few of the ...

    • Recent Articles

    • Removing carriage board - Julia Extended.

      Carriage board is a small board mounted on the carriage. To remove the carriage board follow the steps below. Note: Remove filament before removing carriage cover. 1. Remove carriage cover. The carriage cover is fastened by 2 screws. Please be ...

    • Sending Gcode to Fracktal care for troubleshooting.

      Analysing the Gcode is one among the primary steps done while troubleshooting issues. The gcode which may be fine in your system may get corrupted while uploading to your printer. To make sure this corruption has not happened we recommend analysing ...

    • Material (filament) storage SOP

      3D printing filaments are hygroscopic in nature. PLA Nylon and PVA are extremly hygroscopic and storing them in air tight containers with dessicants is a must. Other filaments also need to be stored in air tight container but can be exposed to ...

    • SMPS not turning ON

      SMPS may not turn because of these reasons. 1. SMPS is not getting power supply. 2. SMPS is spoilt 3. SMPS is detecting a short in machine circuit and is auto Shutting. Troubleshooting: Note: Checking SMPS input when machine is on is risky task. You ...

    • Changing SMPS- Extended.

      Fractal Printers are designed with serviceability in mind. Changing SMPS in Julia Extended can be done with the help of a + Screw driver and 2.5mm Allen key (Allen Key is provided with the Accessory box).  Steps to replace SMPS: 1. Switch off the ...