Julia Extended and Intermediate User Manual (2018)
Related Articles
Changing SMPS- Extended.
Fractal Printers are designed with serviceability in mind. Changing SMPS in Julia Extended can be done with the help of a + Screw driver and 2.5mm Allen key (Allen Key is provided with the Accessory box). Steps to replace SMPS: 1. Switch off the ...
Removing carriage board - Julia Extended.
Carriage board is a small board mounted on the carriage. To remove the carriage board follow the steps below. Note: Remove filament before removing carriage cover. 1. Remove carriage cover. The carriage cover is fastened by 2 screws. Please be ...
Layer Shifting caused by pulley slipping down
Motor Pulley is mounted on Motor shaft with the help of a grub screw. The pulley acts as a bridge for transferring the motors rotary motion to the belts. The motor pulley comes under high stresses and sometimes may get displaced. The displacement of ...
Thermal Runway, System Stopped Error
Fracktal printers come with inbuilt feature to avoid accidents by over heating of the nozzle or heater cartridge. Due to some issue with printer if the heater cartridge heats beyond certain temperature it can lead to melting of hot end and also fire ...
Popular Articles
Buying a 3D printer.
3D printing technology is broadly classified into FDM, SLA and SLS printing. We at Fracktal works Manufacture and sell machines related to FDM and SLA. If you need parts printed using SLS you can use our Fractory service. We have mentioned few of the ...
Fracktory software, User manual and Quick start Video
Here is the download link for the latest Fracktory: http://printers.fracktory.in/download Kindly register with us via the software to avail special offers and updates from Fracktal. The user manual also describes the best practices to use the ...
Hotend Assembly
The hotend assembly * Nozzle (0.4mm) * Heater block (Steel block) * Heating cartridge * Thermistor Nozzle swap procedure: * To replace the nozzle, first wait for the nozzle to cool down. Then gently pull down the (green) connector. * Use an M3 allen ...
Build plate related issues
The aluminum build plate and PET sheets are consumables and not covered under warranty. Over time, the build plate will might wear out and and lead to print inconsistencies due to irregular surface. The cost of replacing the build plate is INR ...
Taxation in the 3D Printing Industry (FDM only :)
This is for the "3D Printer" Printing machinery used for printing by means of plates, cylinders and other printing components of heading 84.42; Printers [other than machines which perform two or more of the functions of printing, copying or facsimile ...
Recent Articles
Removing carriage board - Julia Extended.
Carriage board is a small board mounted on the carriage. To remove the carriage board follow the steps below. Note: Remove filament before removing carriage cover. 1. Remove carriage cover. The carriage cover is fastened by 2 screws. Please be ...
Sending Gcode to Fracktal care for troubleshooting.
Analysing the Gcode is one among the primary steps done while troubleshooting issues. The gcode which may be fine in your system may get corrupted while uploading to your printer. To make sure this corruption has not happened we recommend analysing ...
Material (filament) storage SOP
3D printing filaments are hygroscopic in nature. PLA Nylon and PVA are extremly hygroscopic and storing them in air tight containers with dessicants is a must. Other filaments also need to be stored in air tight container but can be exposed to ...
SMPS not turning ON
SMPS may not turn because of these reasons. 1. SMPS is not getting power supply. 2. SMPS is spoilt 3. SMPS is detecting a short in machine circuit and is auto Shutting. Troubleshooting: Note: Checking SMPS input when machine is on is risky task. You ...
Changing SMPS- Extended.
Fractal Printers are designed with serviceability in mind. Changing SMPS in Julia Extended can be done with the help of a + Screw driver and 2.5mm Allen key (Allen Key is provided with the Accessory box). Steps to replace SMPS: 1. Switch off the ...