Fracktory software, User manual and Quick start Video

Fracktory software, User manual and Quick start Video

Here is the download link for the latest Fracktory:

http://printers.fracktory.in/download


Kindly register with us via the software to avail special offers and updates from Fracktal.

The user manual also describes the best practices to use the software. One can also download a user manual PDF for Julia Plus and Fracktory via gallery below.

Below is a link for the quick setup and bed calibration procedures. Kindly refer to the video once before self-installation.

Thank you for trusting us with your 3D Printing requirements. :) 

Sincerely,
Team Fracktal
support@fracktal.in
    • Related Articles

    • Software Update procedure for Wifi connected Julia Series

      Please watch the video attached to know how to push new software update to your wifi connected Julia Series of 3D Printers. Current version updates: 1. Wifi network recognition of hidden connections 2. Improved UI features  3. Faster functionality. ...
    • Manual for Julia 2018 Series

      Access to Manual
    • Nylon with Julia+

      Nylon filament is compatible with Julia +.  There is no existing configuration file available with the software for Nylon. Here is a new configuration file for it. Just directly drag and drop it into fracktory. Also, nylon absorbs moisture so please ...
    • USB Setup guide

      This is the link for the driver executable file, https://cdn.sparkfun.com/assets/learn_tutorials/7/4/CDM_v2.12.00_WHQL_Certified.exe.  When you are installing the driver, make sure to "Run as Administrator", you can find that by right clicking on the ...
    • Bed Levelling Knob holder - 3D Printable part

      Here's a download link of the STL file that can be 3D Printed for a quick replacement. Download Link However, we strongly suggest you purchase a metal replacement part by contacting out support team. Happy printing! Team Fracktal
    • Popular Articles

    • Fracktory software, User manual and Quick start Video

      Here is the download link for the latest Fracktory: http://printers.fracktory.in/download Kindly register with us via the software to avail special offers and updates from Fracktal. The user manual also describes the best practices to use the ...
    • Hotend Assembly

      The hotend assembly * Nozzle (0.4mm) * Heater block (Steel block) * Heating cartridge * Thermistor  Nozzle swap procedure: * To replace the nozzle, first wait for the nozzle to cool down. Then gently pull down the (green) connector. * Use an M3 allen ...
    • Build plate related issues

        The aluminum build plate and PET sheets are consumables and not covered under warranty.   Over time, the build plate will might wear out and and lead to print inconsistencies due to irregular surface. The cost of replacing the build plate is INR ...
    • Taxation in the 3D Printing Industry (FDM only :)

      This is for the "3D Printer" Printing machinery used for printing by means of plates, cylinders and other printing components of heading 84.42; Printers [other than machines which perform two or more of the functions of printing, copying or facsimile ...
    • Nylon with Julia+

      Nylon filament is compatible with Julia +.  There is no existing configuration file available with the software for Nylon. Here is a new configuration file for it. Just directly drag and drop it into fracktory. Also, nylon absorbs moisture so please ...
    • Recent Articles

    • Removing carriage board - Julia Extended.

      Carriage board is a small board mounted on the carriage. To remove the carriage board follow the steps below. Note: Remove filament before removing carriage cover. 1. Remove carriage cover. The carriage cover is fastened by 2 screws. Please be ...
    • Sending Gcode to Fracktal care for troubleshooting.

      Analysing the Gcode is one among the primary steps done while troubleshooting issues. The gcode which may be fine in your system may get corrupted while uploading to your printer. To make sure this corruption has not happened we recommend analysing ...
    • Material (filament) storage SOP

      3D printing filaments are hygroscopic in nature. PLA Nylon and PVA are extremly hygroscopic and storing them in air tight containers with dessicants is a must. Other filaments also need to be stored in air tight container but can be exposed to ...
    • SMPS not turning ON

      SMPS may not turn because of these reasons. 1. SMPS is not getting power supply. 2. SMPS is spoilt 3. SMPS is detecting a short in machine circuit and is auto Shutting. Troubleshooting: Note: Checking SMPS input when machine is on is risky task. You ...
    • Changing SMPS- Extended.

      Fractal Printers are designed with serviceability in mind. Changing SMPS in Julia Extended can be done with the help of a + Screw driver and 2.5mm Allen key (Allen Key is provided with the Accessory box).  Steps to replace SMPS: 1. Switch off the ...